Μετάβαση στο περιεχόμενο
Elausys

KNX Πύλες για Inverters / Εγχειρίδιο χρήσης INV-KNX Fronius

Θέση σε λειτουργία ETS

Φυσική διεύθυνση, παράμετροι εφαρμογής, συνδέσεις διευθύνσεων ομάδας και λήψεις ETS για το INV-KNX Fronius.

elausys · 13 Σεπτεμβρίου 2026
Σε αυτή τη σελίδα

Ανάθεση φυσικής διεύθυνσης

Add the appropriate Elausys INV-KNX application to the ETS project. Choose an unused physical address in the project topology; Press the gateway P button to enter programming mode and download the physical address.

Ρύθμιση παραμέτρων εφαρμογής

Once a KNX physical address is set, open the parameter tab to configure the interface.

Select the type of AC network (single phase or tri-phase).

Set the inverter model to 3 for Fronius inverters or 6 for Fronius Symo Hybrid inverters.

Choose the refresh rate (min) for the complete set of data.

Select if battery 1 is available on the inverter.

Select Powermeter if a Fronius Smart Meter is available.

Fronius Smart meter modbus ID must be set in the “Device Options” field.

Smartmeter ID must be checked in the inverter configuration (default is 200 or 240).

Set the timezone and daylight-saving option when using weekly calendar logic. See Section 6 for the full parameter values and limitations.

Σύνδεση αντικειμένων και λήψη εφαρμογής

A group address (GA) must be assigned to each group object (GO) needed by the application.

Open the Group Objects tab of the device and assign a GA to the objects as needed.

When GO and parameters are all configured, download the KNX Interface application to the device. The first download requires to press the programming button on the device to set the device in KNX programming mode then perform a full download.

Έλεγχος αποτελέσματος

Use ETS Group Monitor to check module status, read the firmware version and compare live measurements with the inverter. Follow Section 7 before enabling automation.

Λογισμικό ETS

The gateway is configured with ETS from the KNX Association. ETS Demo supports projects of up to five KNX modules; the gateway occupies one module.

Πλοήγηση στο εγχειρίδιο

All chapters of the INV-KNX Fronius user manual

Συχνές ερωτήσεις

Τι απαιτείται για την πρώτη λήψη ETS;

Αναθέστε τη φυσική διεύθυνση χρησιμοποιώντας το κουμπί P για τη λειτουργία προγραμματισμού. Διαμορφώστε τις παραμέτρους εφαρμογής και τις απαιτούμενες συνδέσεις διευθύνσεων ομάδας και εκτελέστε πλήρη λήψη.

Τι πρέπει να ελέγξω μετά τη λήψη της εφαρμογής;

Χρησιμοποιήστε το ETS Group Monitor για να διαβάσετε την κατάσταση της μονάδας και το firmware και, μετά το διάστημα polling, συγκρίνετε τις ζωντανές μετρήσεις με τον μετατροπέα.

Συνεχίστε την εξερεύνηση

Βρείτε τους υπόλοιπους οδηγούς για αυτό το προϊόν στην τεκμηρίωση.

Επιστροφή στο Εγχειρίδιο χρήσης INV-KNX Fronius