Μετάβαση στο περιεχόμενο
Elausys

KNX Πύλες για Inverters / Εγχειρίδιο χρήσης INV-KNX Fronius

Γρήγορη θέση σε λειτουργία

Η διαδικασία θέσης σε λειτουργία του INV-KNX Fronius, από την καλωδίωση έως τις επικυρωμένες μετρήσεις KNX.

elausys · 10 Σεπτεμβρίου 2026
Σε αυτή τη σελίδα

Follow these steps in order. Use the detailed sections for model-specific settings and the complete object reference.

1 Προετοιμασία της εγκατάστασης

Have the gateway, KNX bus connection, 12-30 VDC auxiliary supply, network connection, ETS application and inverter configuration access ready. Check compatibility and firmware in Sections 3 and 10.

2 Σύνδεση και τροφοδοσία της πύλης

Connect KNX at the top. Connect auxiliary power and RJ45 Ethernet at the bottom. Connect the equipment to the same local network. The green Network LED confirms the Ethernet link; see Section 3.

3 Διαμόρφωση της σύνδεσης του μετατροπέα

Enable Modbus TCP or configure the required inverter connection using Section 4. Confirm the inverter address, port and Unit ID.

4 Ρύθμιση δικτύου και σύνδεσης Modbus

Open 192.168.1.51 from a laptop on a compatible network and assign an appropriate fixed gateway IP address. Set Mode to Connect, Server IP to the inverter address, Server Port to 502 and Unit ID to 1.

5 Διαμόρφωση της συσκευής KNX στο ETS

Assign a free physical address. Set Inverter model to 3 for Fronius including Gen24; 6 for Fronius Symo Hybrid. Set the AC network, applicable PV circuits, refresh rate and available equipment. Set Device Options to the Fronius Smart Meter Modbus ID when a meter is installed; check the actual ID (default 200 or 240). See Sections 5 and 6.

6 Σύνδεση διευθύνσεων ομάδας και λήψη

Assign group addresses to the required objects. Press P when ETS requires programming mode and perform a full application download for initial commissioning. See Section 5.

7 Επικύρωση δεδομένων και ενεργοποίηση λογικής

Check the Connected LED and Module status (GO 1 = 0). Read firmware (GO 2), wait for the polling interval and compare live values with the inverter. Check power directions and optional equipment before enabling logic. See Section 7.

Commissioning is complete when

The network and inverter links are established, the ETS download succeeds, and the required group objects return plausible values for the installed equipment.

Πλοήγηση στο εγχειρίδιο

All chapters of the INV-KNX Fronius user manual

Συχνές ερωτήσεις

Τι πρέπει να είναι έτοιμο πριν από τη θέση σε λειτουργία;

Προετοιμάστε την πύλη, βοηθητική τροφοδοσία 12–30 VDC, το bus KNX, τις συνδέσεις δικτύου, την εφαρμογή ETS και πρόσβαση στη διαμόρφωση του μετατροπέα.

Αποδεικνύει το LED Network ότι ολοκληρώθηκε η θέση σε λειτουργία;

Όχι. Το LED Network επιβεβαιώνει τη φυσική σύνδεση Ethernet. Ελέγξτε το Connected, ολοκληρώστε τη λήψη ETS και συγκρίνετε τις τιμές KNX με τον μετατροπέα.

Πότε πρέπει να ενεργοποιήσω αυτοματισμό με βάση δεδομένα μετατροπέα;

Ελέγξτε την κατάσταση της μονάδας, το διάστημα polling, τις ζωντανές μετρήσεις, τις κατευθύνσεις ισχύος και τον προαιρετικό εξοπλισμό.

Συνεχίστε την εξερεύνηση

Βρείτε τους υπόλοιπους οδηγούς για αυτό το προϊόν στην τεκμηρίωση.

Επιστροφή στο Εγχειρίδιο χρήσης INV-KNX Fronius